APOLLO 7
True Wireless Earphones
Available in Grey, Silver, Gold, and Rose Gold
True Wireless Earphones
Available in Grey, Silver, Gold, and Rose Gold
When using for the first time, please fully charge earphones for approx. 2 hours.
NOTE:
APOLLO 7 are designed with a single-touch a multi-function feature that allows you to fully control your device with just one button.
MODES
• Stand-by Mode – no audio is active or music is paused.
• Media Mode – music or video are active.
• Hands-free Mode – during a phone conversation only the Master earphone will be active.
*The Master earphone is the earphone that is paired to your device.
POWERING ON
Long press LEFT and RIGHT button for 2 seconds. Listen for voice prompts.
POWERING OFF
From Stand-by or Hands-free Mode, long press for 2 seconds either LEFT or RIGHT button.
ANSWERING INCOMING CALL
Press the Master earphone button.
REJECTING INCOMING CALL
Long press Master earphone button for 2 seconds.
ENDING CALL
Press button on the Master earphone.
INCREASE/DECREASE HANDS-FREE VOLUME
Can only be adjusted by your device.
ACTIVATING SIRI/GOOGLE NOW (for supported devices only)
From Stand-by Mode, double press LEFT or RIGHT button.
PLAY/PAUSE MUSIC
During Stand-By or Media Mode, press LEFT or RIGHT button to play/pause media.
INCREASE/DECREASE MEDIA VOLUME*
Increase: During Media Mode, double press RIGHT button. A double beep indicates volume is at maximum level.
Decrease: During Media Mode, double press LEFT button.
NEXT SONG
Next Song: During Media Mode, long press RIGHT button for 2 seconds.
RESTART/PREVIOUS SONG
Restart/Previous Song: During Media Mode, long press LEFT button for 2 seconds to restart the song, then again to go to the previous song.
NOTE:
* Android and non-iOS devices: Increasing or decreasing the volume on your APOLLO 7 do not affect your host device’s volume, increase device’s volume in conjunction with APOLLO 7 to desire safe levels.
** The APOLLO 7 is optimized for the latest iOS and Android devices. Functionality will vary from device and app.
The APOLLO 7 charging case will allow two full charges of your earphones while on the go.
OPENING
To open the charging case, simply push the end of the case. This action can be done with just one finger and remove the earphones.
CLOSING
When you are done with your APOLLO 7, simply insert them back in its protective charging case and feel for the click, indicating that it is securely locked.
TIP: Rotate the earphones so that the LED’s light are facing you. Look for a red light to indicate the earphones are charging
NOTE: Earphones will automatically power off once inserted into charging case.
EARPHONES CHARGING INDICATOR
CHARGING CASE INDICATOR
NOTE:
• If earphone battery is less than 5%, you will hear a “Low battery” reminder every 30 seconds.
* The playback time will vary depending on the sound quality and the conditions under which you are using the APOLLO 7.
** Time necessary for charging the empty battery to its full capacity.
For optimal comfort and sound quality please try the silicone/Comply Isolation 600 (T-600) tips that best suit your ears. Simply gently pull on the tip from the earphone (please be extra gentle when removing Comply tips). You may need to try different size combinations for your left and right ear.
TIP: For optimal connectivity, please ensure that the earphone button is pointed upwards.
STABILIZERS
The stabilizers are great when you need that extra security. Simply remove the tip, install them onto the earphone, and put the tip back on.
Comply Isolation T-600 (http://www.complyfoam.com/products/t-600/)
Usage hours may be shorter depending on the codec and the conditions of use. For prolonging the usage of the earphones, please set the volume to a moderate level and lower audio bitrate when possible
In True Wireless, instead of one Bluetooth receiver, there are two and data have to be transmitted twice which can cause latency issue in playing video/audio. The earphones require the data to buffer about 20-80 millisecond (ms) to prevent signal drop-out between earphones, which can cause latency when watching a video.
Devices and apps that your earphones are paired to could compensate by adding a slight video delay to synchronize with the Bluetooth latency. As an accessory manufacturer, we do not have such control over the devices and app that are used with our earphones and we are looking into future improvements that would help with the latency issue.
To minimize the latency when watching a video, we ask you to lower the bit rate of the audio if possible and move the host device closer to the Master earphone so to reduce any environmental interference between the devices.
Due to safety reason, only one earbud will work for phone calls so you are able to hear out the other ear. Make sure on your device under Bluetooth that the Apollo 7’s are set to receive phone calls.
APOLLO 7 can store up to 8 devices profiles, however, only ONE active profile can be used at a time.
Once paired beyond the 8 devices limit, the first profile will be remove followed by the second and so forth.
Signal drop occurs when there is interference between the earphones or the host device which causes data loss during transmission, this a relatively normal occurs with wireless devices.
If you are experiencing a high amount of signal drop, try moving the host device closer to the Master earphones to see if the situation improve. Also, make sure that the earphones are pointed upwards to improve the connection and try to avoid areas with high-level of radio interference like cellular towers and Wi-Fi routers.
Erases all Bluetooth profiles and restore back to factory specifications.
Android and non-iOS devices: Turn up the volume on the earphones AND on your host device. The volume controls are independent of each other when listening to music/media.
For Hands-free volume is controlled by the host device, increase the volume on your host device.
If your Apollo 7 earphones are not charging try these simple troubleshooting steps:
Bluetooth | Bluetooth 4.1 | |
BT Profile | A2DP 1.2, AVRCP 1.4, HFP 1.6, HSP 1.2 | |
Audio Codec | aptX, AAC, SBC | |
Driver | Ø 5.8mm Microdriver | |
Sensitivity | 100db/1mW | |
Frequency | 20Hz ~ 20kHz | |
Impendence | 16 Ohm | |
Microphone MEMS Omnidirectional | -42dB (±2dB) | |
Waterproof | Nanocoating IPX5 Water/Sweat Resistant | |
3D Audio | Not Compatible | |
Battery Life | 3 hours play time 4 hours talk time |
|
Dimensions | Earphones: 15.4mm(L) x 22.22mm(D)
Charging Case: 62.5mm(L) x 40mm(D) x 25.5mm(H) |
|
Weight | Earphone: 4 g x 2 (0.14 oz x 2)
Charging Case: 52 g (1.83 oz) |
EN – Apollo 7 User Manual
AR – Apollo 7 User Manual
CZ – Apollo 7 User Manual
DE – Apollo 7 User Manual
ES – Apollo 7 User Manual
FR – Apollo 7 User Manual
HU – Apollo 7 User Manual
ID – Apollo 7 User Manual
IT – Apollo 7 User Manual
JP – Apollo 7 User Manual
KR – Apollo 7 User Manual
KZ – Apollo 7 User Manual
NL – Apollo 7 User Manual
PL – Apollo 7 User Manual
PT – Apollo 7 User Manual
RU – Apollo 7 User Manual
SC – Apollo 7 User Manual
TC – Apollo 7 User Manual
TH – Apollo 7 User Manual
TR – Apollo 7 User Manual
UA – Apollo 7 User Manual
VN – Apollo 7 User Manual